View LS020Q3UX03_2777752.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www.datasheet.co.kr datasheet pdf - http://www..net/
www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 1 notice these specification sheets are the proprietary product of sharp corporation ("sharp) and include materials protected under copyright of sharp. do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpos e, in whole or in part, without th e express written permission of sharp. the application examples in these specifi cation sheets are provided to explain the representative applications of the device a nd are not intended to guarantee any industrial property right or other rights or license you to use them. sharp assumes no responsibility for any problems related to any industrial propert y right of a third party resulting from the use of the device. the device listed in these specification sheets was designed and manufactured for use in telecommunication equipment (terminals) in case of using the device for applications such as contro l and safety equipment for transportation (aircraft, trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures su ch as fail-safe functions and redundant system design should be taken. do not use the device for equipment th at requires an extreme level of relia bility, such as aerospace applications, telecommunication equipment (trunk lines), nuclear power contro l equipment and medical or other equipment for life support. sharp assumes no responsibility for any damage resulting fro m the use of the device which does not comply with the instructions and the precautions speci fied in these specification sheets. contact and consult with a sharp sales representative for any questions about this device. [for handling and system design] (1) do not scratch the surface of the pol arizer film as it is easily damaged. (2) if the cleaning of the surface of the lcd panel is necessary, wipe it swiftly with cotton or other soft cloth. do not use organic solvent as it damages polarizer. (3) water droplets on polarizer must be wiped off immediately as th ey may cause color changes, or other defects if remained for a long time. (4) since this lcd panel is made of glass, dropping the module or banging it against hard objects may cause cracks or fragmentation. (5) certain materials such as e poxy resin (amine?s hardener) or silicone adhesive agent (de-alc ohol or de-oxym) emits gas to which polarizer reacts (color change). check carefully that gas from materials used in system housing or p ackaging do not hart polarizer. (6) liquid crystal material will freeze belo w specified storage temperature range a nd it will not get back to normal quality ev en after temperature comes back w ithin specified temperature range. liquid crystal material will become isotropic above specified temperature range and may not get back to normal quality. keep the lcd module always within specified temperature range. (7) do not expose lcd module to the direct sunlight or to strong ultraviolet light for long time. (8) if the lcd driver ic (cog) is exposed to light, normal operation may be impeded. it is necessary to design so that the lig ht is shut off when the lcd module is mounted. (9) do not disassemble the lcd module as it may cause permanent damage. (10) as this lcd module contains components sensitive to electrostatic discharge, be sure to follow the in structions in below. operators operators must wear anti-static wears to prevent el ectrostatic charge up to and discharge from human body. equipment and containers process equipment such as conveyer, soldering iron, worki ng bench and containers may possibly generate electrostatic www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 2 charge up and discharge. equipment must be grounded through 100mohms resistance. use ion blower. floor floor is an important part to leak static electricity which is generated from human body or equipment. there is a possibility that the static el ectricity is charged to them without l eakage in case of insulating floor, so the countermeasure(electrostatic earth:1 10 8 ) should be made. humidity proper humidity of working room may reduce the risk of electro static charge up and discharge. humidity should be kept over 50% all the time. transportation/storage storage materials must be anti-static to prevent causing electrostatic discharge. others protective film is attached on the surf ace of lcd panel to prevent scratches or other damages. when removing this protective film, remove it slowly under proper anti-esd control such as ion blower. (11) hold lcd very carefully when placing lcd module into the system housing. do not apply excessive stress or pressure to lcd module. do not to use chloroprene rubber as it may affect on the reliability of th e electrical interconnection. (12) do not hold or touch lcd panel to flex interconnection area as it may be damaged. (13) as the binding material between lcd panel and flex connect or mentioned in 12) contains an organic material, any type of organic solvents are not allowed to be used. direct contact by fingers is also prohibited. (14) when carrying the lcd module, place it on the tray to protect from mechanical damage. it is recommended to use the conductive trays to protect the cmos components from electrostatic discharge. when holding the module, hold the plastic frame of lcd module so that the panel, cog and other electric parts are not damaged. (15) do not touch the cog?s patterning area. otherwise the circuit may be damaged. (16) do not touch lsi chips as it may cause a trouble in the inner lead connection. (17) place a protective cover on the lcd module to pr otect the glass panel from mechanical damages. (18) lcd panel is susceptible to mechani cal stress and even the slightest stress w ill cause a color change in background. so make sure the lcd panel is placed on flat plane wit hout any continuous twisting, bending or pushing stress. (19) protective film is placed onto the surf ace of lcd panel when it is shipped from fact ory. make sure to peel it off before assembling the lcd module into the system. be very careful not to damage lcd module by electrostatic discharge when peeling off this protective film. ion blower and ground strap are recommended. (20) make sure the mechanical design of the system in which the lcd module will be assembled matches specified viewing don?t don?t do do don?t don?t do do www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 3 angle of this lcd module. (21) this lcd module does not contain nor use any ods (1,1,1-trichloroethane, ccl4) in all materials used, in all production processes. [for operating lcd module] (1) do not operate or store th e lcd module under outside of speci fied environmental conditions. (2) at the shipment, adjust the contrast of each lcd module with electric volume. lc d contrast may vary from panel to panel depending on variation of lcd power voltage from system. (3) as opt-electrical characteristics of lcd will be changed, dependent on the temperature, the confirmation of display quality and characteristics has to be done after temperature is set at 25 c and it becomes stable. [precautions for storage] (1) do not expose the lcd module to direct sunlight or strong ultraviolet light for long periods. store in a dark place. (2) the liquid crystal material will solidify if stored below the rated storage temperature and will become an isotropic liquid if stored above the rated storage temperature, and may not retain its original properties. only store the module at normal temperature and humidity (25 5c,60 10%rh) in order to avoid exposing the front polarizer to chronic humidity. (3) keeping method a. don't keeping under the direct sunlight. b. keeping in the tray under the dark place. (1) do not operate or store th e lcd module under outside of speci fied environmental conditions. (2) be sure to prevent light striking the chip surface. do don?t www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 4 [other notice] (1) do not operate or store th e lcd module under outside of speci fied environmental conditions. (2) as electrical impedance of power supply lines (vcc2-vss) are low when lcd module is working, place the de-coupling capacitor near by lcd module as close as possible. (3) reset signal must be sent after power on to initialize lsi. lsi does not function properly until initialize it by reset sig nal. (4) generally, at power on, in order not to apply dc charge directly to lcd panel, supply logic voltage first and initialize ls i logic function including polarity alternation. then supply voltage fo r lcd bias. at power off, in order not to apply dc charge directly to lcd panel, execute power off sequence and discharge command. (5) don?t touch to pwb surface, exposed ic chip, electric pa rts and other parts, to any electric, metallic materials. (6) no bromide specific fire-retardant material is used in this module. (7) do not display still picture on the display over 2 hours as this will damage the liquid crystal. [precautions for discarding liquid crystal modules] cog: after removing the lsi from the liquid crystal panel, dispose of it in a similar way to circuit boards from electronic devices. lcd panel: dispose of as glass waste. this lcd module contai ns no harmful substances. the liquid crystal panel contains no dangerous or harmful substances. the liquid crystal panel only contains an extremely small amount of liquid crystal (approx.100mg) and therefore it will not l eak even if the panel should break. -its median lethal dose (ld50) is greater than 2,000 mg/kg and a mutagenetic (aims test: negative) material is employed. fpc: dispose of as similar way to circuit board from electric device. www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 5 1. application this data sheet is to introduce the specification of LS020Q3UX03 active matrix 262,144color lcd module. main color lcd module is controlled by driver ic (jbt6k85). if any problem occurs concerning the items not stated in this specification, it must be solved sincerely by both parties after deliberation. as to basic specification of driver ic refer to the ic specification and handbook. 2. construction and outline construction: lcd panel, driver (cog), fpc with electric components, (3) white led lump, prism sheet, diffuser, light guide a nd reflector, plastic frame to fix them mechanically. outline: see page 31 connection: 35 pins; 0.3mm pitch there shall be no scratches, stains, chips, distortions and ot her external drawbacks that ma y affect the display function. rejection criteria shall be noted in inspection standard (s-u-056-xx) in order to realize thin module structure, double-sided adhe sive tapes are used to fix lcd panels. as these tapes do not guarantee to permanently fix the panels, lcd panel may rise from the module when shipped from factory. so please make sure to design the system to hold the edges of lcd panel by the soft material such as sponge when lcd module is assembled into the cabinet. 3. mechanical specification table 1 parameter specifications unit outline dimensions (typ) 37.2 (w) 65.10 (h) 1.9 (d) mm active area 30.60 (w) 40.80 (h) mm viewing area 31.60 (w) 41.80 (h) mm display format 240 rgb(w) 320(h) - dot pitch 0.0425 (w) 0.1275 (h) mm main lcd panel base color *1 normally black - mass approx 5.6 g *1 due to the characteristics of the lc material, th e colors vary with environmental temperature. www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 6 4. absolute maximum ratings (4-1) electrical absolute maximum ratings table 2 ta=25 parameter symbol min max unit remark vcc1-gnd -0.3 4.6 supply voltage vcc2-gnd -0.3 4.6 input voltage v in -0.3 vcc1+0.3 *1 *1 input terminal of logic system. : voltage value is based on gnd = 0v. environment conditions table 3 top tstg remark item min. max. min. max. ambient temperature -10 c +60c -20 c +70c note 2) humidity note 1) note 1) no condensation note1) ta 40 c.......95 % rh max note2) ta > 40 c.......absolute humidity sh all be less than ta=40 c /95 % rh. as opt-electrical characteristics of lcd will be changed, dependent on the temperature, the confirmation of display quality and characteristics has to be done after temperature is set at 25 c and it becomes stable. be sure not to exceed the rated voltage, otherwise a malfunction may occur. www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 7 5. electrical specifications (5-1) electrical characteristics for main lcd table 4 ta=25 , gnd=0v parameter symbol conditions min. typ. max. unit applicable pin supply voltage vcc1 - vss ta=-10 60 c 1.65 2.60 3.60 v (note 1) supply voltage vcc2 - vss ta=-10 60 c 2.70 2.80 2.90 v (note 1) ?h? level input voltage v ih1 0.7 v cc1 - - v (note 2) ?l? level input voltage v il1 ta=-10 60 c - - 0.3 v cc1 v (note 2) input leakage current i li1 -10 - 10 a (note 2) output leakage current i lo ta=-10 60 c v in = gnd or vcc1 -10 - 10 a (note 3) ?h? level output voltage v oh1 0.8 v cc1 - - v ?l? level output voltage v ol1 ta=-10 60 c i oh1 =-1 ma , i ol1 = 1 ma - - 0.2 v cc1 v (note 4) current consumption i cc2 ta=25 c - 6.3 9.0 ma (note 5) (note 1) the condition vcc1 vcc2 must be met (note 2) input mode of d0 d15pins, a0, rd, wr, cs, reset (note 3) output mode of d0 d15pins. (note 4) output mode of d0 d15 pins. (note 5) following conditions ta=25 frame frequency=65hz display pattern: rgb checker pattern. no host cpu access. rgb checker pattern www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 8 (5-2) led back light 1 (1) at main panel the back light uses 3pcs edge light type white led. table 5 parameter conditions symbol min. typ. max. unit remark forward current ta=25 c i led - 20 *1 - ma vled- led_cathode1~3 led lamp: gm4bw63374a ( sharp corporation) ([luminous intensity rank]: e2, f1 or f2 [color rank]: b54 or b56 or b83) *1 per one piece of led *please consider allowable forw ard current on used temperature (refer to ambient temperature vs. allowable forward current curve) www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 9 (5-3) interface signals table 6 pin no symbol description i/o remarks 1 vled led1~3 anode common - 2 led cathode1 led1 cathode - 3 led cathode2 led2 cathode - 4 led cathode3 led3 cathode - 5 vcc2 power supply (lcd driver) for analog - 6 vcc1 power supply (lcd driver) for i/o - 7 id vendor identify - connected to vcc1 8 d15 data bus i/o 9 d14 data bus i/o 10 d13 data bus i/o 11 d12 data bus i/o 12 d11 data bus i/o 13 d10 data bus i/o 14 d9 data bus i/o 15 d8 data bus i/o 16 d7 data bus i/o 17 d6 data bus i/o 18 d5 data bus i/o 19 d4 data bus i/o 20 d3 data bus i/o 21 d2 data bus i/o 22 d1 data bus i/o 23 d0 data bus i/o 24 gnd gnd level pin - 25 gnd gnd level pin - 26 rd read enable i low enable 27 wr write enable i low enable 28 a0 data / command selectable i l ow: command h igh: display data / parameter 29 cs chip select i low enable 30 vnsco tearing effect output o 31 if2 bus width setting i refer to circuit diagram 32 if1 bus width setting i refer to circuit diagram 33 reset reset enable i low enable 34 gnd ground level pin 35 gnd ground level pin corresponded connector : 0.3mm pitch, zif connector (omron xf2b-3545-31a) signals connect to lcd module. symbols correspond able to circuit diagram in page 30. www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 10 (5-4) host interface timing diagrams (80-family mpu access) for jbt6k85 www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 11 condition : nomal write mode, vddio=1.65 2.4v, ta = 25 note : tdd and tdhr are measured with the load as shown in the figure. condition : high speed write mode, vddio=1.65 2.4v, ta = 25 note : tdd and tdhr are measured with the load as shown in the figure. www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 12 condition : nomal write mode, vddio=2.4 3.6v, ta = 25 note : tdd and tdhr are measured with the load as shown in the figure. condition : high speed write mode, vddio=2.4 3.6v, ta = 25 note: tdd and tdhr are measured with the load as shown in the figure. www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 13 (5-6) schematic of lcd module system fig.1 schematic of lcd module system (5-7) circuit diagram see page 30 www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 14 6. optical characteristics 1 table 7 vcc1=2.6v, vcc2=2.8v,ta = 25 o p tical characteristics paramete r s y mbol conditio min typ max uni t remar k brightness br =0 220 320 - cd/ O note1,2,5 contrast co =0 300 500 - note1,3 11 70 80 - 12 70 80 - 21 70 80 - viewing angle 22 co > 5 70 80 - deg note1 rise r1 -1122ms response time deca y d1 =0 -2448ms note1,4 x 0.245 0.295 0.345 white chromaticity y =0 0.26 0.31 0.36 x 0.60 0.65 0.70 red chromaticity y =0 0.29 0.34 0.39 x 0.27 0.32 0.37 green chromaticity y =0 0.58 0.63 0.68 x 0.09 0.14 0.19 blue chromaticity y =0 0.01 0.05 0.10 note.1,3 uniformit y - =0 70 - - % n ote.6 n tsc ratio - =0 60 70 - % color tem p erature - =0 6000 7900 10000 k flicker ratio - *1 - - 7 % *1: measuring condition ? measuring systems: yokogawa 3298_01 + 3298_11 ? temperature = 25 ( 3 ), frame frequency = 65hz (-0/+5hz), led back-light: on, environment brightness < 150 lx ? measuring pattern : horizontal stripe pattern ? measured sample : new sample before a long term aging. ? flicker ratio is very sensitive to measuring condition. www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 15 =0 21 22 12 11 viewing direction note 1) definition of range of visual angle fig .2 definition of viewing angle note 2) brightness is measured as shown in fig.3, and is defined as the brightness of all pixels ?white? at the center of display area on optimum contrast. fig. 3 optical characteristics test method (brightness) note 3) contrast ratio is defined as follows: co= luminance(brightness) all pixcels ? white ? luminance(brightness) all pixcels ? black ? measurement equipment: topcon(bm-5a) measuring spot size 4.9 mm measuring field 1.0 bm-5a lcd model diffuser light source www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 16 note 4) response time is defined as follows: fig. 4 response time note 5) iled1 3 =20[ma] note 6) uniformity is defined as follows: uniformity = minimum luminance(brightness) in 9 points maximum luminance(brightness) in 9 points photo detector output 100% 90% time 10% 0% white black white fig. 5 measuring point www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 17 7. reliability 1 table. 8 no. test condition judgment criteria 1 temperature cycling -30 80 -30 60min 60min 60min 12cycle per table in below 2 high temp. storage ta=80 96h per table in below 3 low temp. storage ta= -30 96h per table in below 4 humidity operation ta=60 90%rh,white pattern 96h per table in below (polarizer discoloration is excluded) 5 high temp. operation ta=70 ,white pattern 96h per table in below 6 low temp. operation ta= -20 ,white pattern 96h per table in below 7 temp. drift 70 60 ??? -10 -20 1h 1h 1h 1h (10min) (10min) (10min) (10min) 65%rh(over 10 ), 0%rh(under 0 ) per table in below 8 esd discharge resistance: 0 discharge capacitor: 200 pf discharge voltage: 200 v max discharge 1 time to each input line vss of display module is connected gnd of test system ground. per table in below inspection criterion(after test) appearance no crack on the fpc, on the lcd panel alignment of lcd panel no bubbles in the lcd panel no other defects of alignment in active area electrical current within device specifications function / display no broken circuit, no short circuit or no black line no other defects of display www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 18 8. mechanical strength( 1, 2, 3) 1 table. 9 mechanical strength min typ max unit remark 3 point bending 3.5 kgf note.1) cog constant pushing 2.0 kgf note.2) testing condition ? testing systems: tmd-1kn mineba co.,ltd. ? temperature = 25 ( 3 ) ? non operation ? measured sample : new sample before a long term aging. 1. mechanical strength specification shall be out of lg electroni cs 's incoming inspection standard and not applicable to aql. 2. above specification are meaning of the typical lowest values gotten from actual measurement at sampling test. 3. if there are a lot of samples which doesn?t meet the specifications in the standard sampling test , sharp & lg have discussions how to proceed in each case. note.1) 3 point bending test is measured as follows the strength of 3 point bending is defined as the load of pushing bar at when lcd glass is broken. (test condition) pushing bar: tip shape 3mm round shape sweep speed 3mm/min material aluminum or steel position fig. 7 supporter tip shape 3mm(round shape) pitch 36mm material aluminum or steel fig. 6 3point bending test fig. 7 test position www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 19 note.2) cog constant pushing test is measured as follows the strength of cog constant pushing is defined as the load of pushing rod at when lcd glass or driver ic is broken. (test condition) pushing rod: tip diameter 3mm flat shape sweep speed 3mm/min material aluminum or steel position fig. 9 supporter tip shape 3mm pitch 36mm material aluminum or steel fig. 8 cog constant pushing test fig. 9 test position www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 20 9. packaging specifications (9-1) details of packaging 1) packaging materials: table.11 2) packaging style : fig. 10, 11 (9-2) reliability 1) vibration test table.10 the frequency should start at 5 hz and vary continuously. total amplitude 20mm 0.2mm 20mm 0.2mm frequency 5 hz 50 hz 5 hz 50 hz (for 9.8m/s 2 ) 2) drop test drop height: 750mm number of drop: 10 times (drop sequence: 1 corner, 3 edges, 6 faces) (9-3) packaging quantities 500 modules (max) per master carton (9-4) packaging weight 7.6kg (9-5) packaging outline dimensions 360 mm 525 mm 225 mm (h) (packaging materials) table.11 item test frequency 5 hz to 50 hz (3 minutes cycle) direction up-down, left-right , front-back (3 directions) period up-down left-right front-back total 60min 15min 15min 90min 3 minutes parts name materials 1 master carton corrugate card board 2 under pad corrugate card board 3 inside sleeve corrugate card board 4 outside sleeve corrugate card board 5 tray for packaging polystyrene with anti-static treatment + anti-static polystyrene 6 protective bag polyethylene with anti-static treatment 7 opp tape polypropylene 8 bar code label anti-static polyethylene www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 21 fig.10 packaging style (tray for packaging) www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 22 fig. 11 packaging style (master carton for packaging) www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 23 10. initial sequence power on sequence (in case of 16bit 1 time transfer) item rs index/data hex initial condition (db0-15,rs,csb,wrd,rdb,resetb="l") vddio on vdd on wait min. 1ms fix logic initial voltage level reset release (resetb=h) wait min. 10ms deep stand by release 1 l i 0000h wait min. 3 ms deep stand by release 2 l i 0000h wait min. 3 ms deep stand by release 3 l i 0000h wait min. 3 ms the on-chip cr oscillator operation starts l i 0000h h d 0001h wait min. 5ms panel output control l i 0100h h d 0000h wait min. 1us manual sequence enable l i 0101h h d 0000h vgm setting l i 0102h h d 000ah xvdd setting l i 0103h the booster clock mode of avdd and xvdd is dual mode h d 0006h boosting step setting l i 0104h h d 0000h boosting clock of avdd and xvdd l i 0105h h d 0035h vcs1 setting l i 0107h h d 003bh set source driver output direction l i 0001h (from out120 to out1) h d 0127h stv=1h, precharge "on", rgb out put order is normal. l i 0002h h d 1210h display colors mode l i 0007h (in case of 16bit color) 8030h (in case of 18bit color) hd 4030h transfer mode li 0003h (in case of 16bit 1 time transfer) h d 0030h set front porch =56, back porch=8 l i 0008h h d 3808h set the number of clocks in 1h. l i 000dh h d 0002h panel control setting l i 0012h next pa g e 1 1 1 1 www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 24 h d 0402h panel control setting l i 0014h h d 0001h panel control setting l i 0015h h d 6300h panel control setting l i 001ch h d 0000h panel control setting l i 007ah h d 0400h select gamma curve2. l i 0309h h d 0001h set the offset of the vdh/vgs side of positive gamma. l i 030ah h d 0000h set the offset of the vdh/vgs side of negative gamma. l i 030bh h d 0000h panel control setting l i 0100h h d c000h panel control setting l i 0108h h d 0000h wait min. 16ms panel control setting l i 0100h h d ea00h panel control setting l i 0108h h d 0001h wait min. 16ms panel control setting l i 0100h h d fa00h panel control setting l i 0108h h d 0000h ram address setting. x increment start address set. l i 0200h h d 0000h ram address setting. y increment start address set. l i 0201h h d 0000h ram data write l i 0000h l i 0202h h d xxxxh wait min. 16ms switch on gamma gray scale voltage. l i 0100h hd fb0ah wait min. 32ms source output black display l i 0100h hd fdeah wait min. 16ms source output normal display l i 0100h h d fdfah wait min. 16ms power off sequence www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 25 item rs index/data hex source output (black display) l i 0100h hd fdeah wait min. 16ms panel control setting (display off) l i 0100h h d fcc8h wait min. 32ms panel control setting l i 0100h h d c000h panel control setting l i 0108h h d 0002h wait min. 16ms sleep mode l i 0100h h d 0000h panel control setting l i 0108h h d 0000h deep standby l i 001dh h d 0000h wait min. 300ms vdd off vddio off reset = "l" www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 26 11. parts list parts code specification size vendor lcd 240xrgbx320 2.0" sharp polarizer - - nitto driver lsi jbt6k85 -32as(ez,s) toshiba back light - - nihon lights fpc 2layer cu/pi/cu sony chemical led1~3 gm4bw63374a sharp c2 0.01uf/25v 1005 multi c3 4.7uf/6.3v 1608 multi c4 4.7uf/6.3v 1608 multi c6 1.0uf/6.3v 1005 multi c7 1.0uf/6.3v 1005 multi c8 4.7uf/6.3v 1608 multi c9 1.0uf/6.3v 1005 multi c10 1.0uf/6.3v 1005 multi c11 2.2uf/10v 1608 multi c12 4.7uf/6.3v 1608 multi c13 2.2uf/10v 1608 multi c14 0.1uf/10v 1005 multi c15 1.0uf/10v 1005 multi c16 1.0uf/10v 1005 multi c17 1.0uf/10v 1005 multi c18 1.0uf/10v 1005 multi c19 2.2uf/10v 1608 multi c20 2.2uf/16v 2125 multi c21 2.2uf/10v 1608 multi c23 1.0uf/6.3v 1005 multi c24 2.2uf/6.3v 1608 multi c25 0.1uf/16v 1005 multi c26 0.1uf/16v 1005 multi c27 0.1uf/16v 1005 multi r1 3kohm/d 1005 multi r2 20kohm/d 1005 multi r3 30kohm/d 1005 multi www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 27 fpc work layer 1 www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 28 fpc work layer 2 www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 29 parts layout of fpc www.datasheet.co.kr datasheet pdf - http://www..net/
www.datasheet.co.kr datasheet pdf - http://www..net/
www.datasheet.co.kr datasheet pdf - http://www..net/
spec no. lcy-407301a model no. LS020Q3UX03 page 32 11. serial number label identification numbering is specified as follows. 7 e 000001 q product year ( lower 1 digits ) 7: 2007 8: 2008 product month a: january b: february c: march : l: december serial number 000001 999999 factory code 12. lcd module code rule. ls 020 q 3 u x 03 parts type cgs lcd active area size 2.0inch dot format qvga format lcd type transmissive interface type cpu interface polarizer / lcd viewing type clear type / wide viewing angle serial code www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of LS020Q3UX03

	To Download LS020Q3UX03 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .